Compaq 1910 Guía de usuario

Q1910/Q1910s, Q2010/Q2010s, Q2210/Q2210s LCD MonitorsUser Guide

Safety Precautions●Use only a power source and connection compatible with this monitor, as indicated on the label/back plate of the monitor.●Be sure t

Maintenance GuidelinesTo enhance the performance and extend the life of the monitor:●Do not open the monitor cabinet or attempt to service this produc

3 Setting Up the MonitorUnpacking The Monitor1. Unpack the monitor. Make sure all contents are included. Store the packing box.2. Turn off the compute

2. Hold the base and push it onto the bottom of the support column until it snaps into place.Figure 3-1 Installing the monitor base3. Lift the monito

4. Release the base from the column by squeezing the two tabs toward each other. Pull the baseaway from the column as you do so.Figure 3-3 Bottom vie

6. Rock the bottom of the support column until it snaps away from the top portion of the column, whichcovers the support column mounting bracket.Figur

9. Slide the column mounting bracket away from the bottom of the monitor.Figure 3-7 Sliding the column mounting bracket from the monitor10. Remove th

Connecting Monitor CablesConnecting the VGA (Analog) Cable or DVI-D (Digital) CableUse a VGA video cable or a DVI-D cable to connect your monitor to y

Connecting the Audio CableConnect the built-in monitor speakers to the computer by using the audio cable, as shown in the followingillustration:Figure

Connecting the Power Cable1. Follow all Electrical and Power WarningsWARNING! To reduce the risk of electric shock or damage to your equipment:Do not

© 2010 Hewlett-Packard DevelopmentCompany, L.P.Microsoft, Windows, and Windows Vista areeither trademarks or registered trademarksof Microsoft Corpora

Cable ManagementFigure 3-12 Routing cables through the rear of the support columnAdjusting The TiltFor optimal viewing, adjust the screen tilt to you

4 Operating the MonitorCD Software and UtilitiesThe CD that is included with this monitor contains drivers and software that you can install on yourco

Using the Auto Adjustment FunctionYou can easily optimize the screen performance for the VGA input by using the Auto/OK button on themonitor and the a

Side-Panel ControlsControl buttons are located on the right side of the monitor:Figure 4-2 Side-panel control buttons12345No. Icon Description1 Power

Using the On-Screen Display (OSD)An on-screen display is an image superimposed on a screen picture, commonly used by monitors,televisions, VCRs, and D

Icon Main Menu Options Sub-menu Options Description Custom Color Selects and adjusts your own colorscales:R — Sets your own red color levels.G — Sets

Icon Main Menu Options Sub-menu Options Description OSD Timeout Sets the time in seconds that the OSD isvisible after the last button is pressed. The

Icon Main Menu Options Sub-menu Options DescriptionManagement Power-On Status Display Displays the operating status of themonitor each time the monito

Icon Main Menu Options Sub-menu Options Description Version Reports the firmware version of themonitor. Backlight Hours Reports the total hours

Adjusting Screen QualityThe auto adjustment feature automatically fine-tunes the image quality for display size, position, clock,and phase each time a

About This GuideThis guide provides information on setting up the monitor, installing drivers, using the on-screen displaymenu, troubleshooting and te

A TroubleshootingSolving Common ProblemsThe following table lists possible problems, the possible cause of each problem, and the recommendedsolutions:

Problem SolutionUnable to hear audio frombuilt-in speakers.Do the following:●Ensure the source signal is good by using headphones at the source.●Press

●Conditions under which the problem occurred●Error messages received●Hardware configuration●Name and version of hardware and software you are usingLoc

B Technical SpecificationsAll specifications represent the typical specifications provided by HP's component manufacturers; actualperformance may

Specifications: Power Source: 100–240VAC, 50/60 HzPower Consumption: 40 watts (W) maximumSleep Power Consumption: <2 watts (W) typicalTable B-2 M

Specifications: Maximum Graphics Resolution: 1920 x 1080@ 60 Hz analog modeText Mode: 720 x 400Dot Pitch: 0.2480 x 0.2480 mmHorizontal Frequency (ana

Preset Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz)3 800 x 600 37.88 60.324 1024 x 768 48.36 60.005 1280 x 720 45.00 60.006 1280 x 10

C Agency Regulatory NoticesFederal Communications Commission NoticeThis equipment has been tested and found to comply with the limits for a Class B di

Hewlett Packard CompanyP. O. Box 692000, Mail Stop 530113Houston, Texas 77269-2000Or, call 1-800-HP-INVENT (1-800 474-6836)For questions regarding thi

Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GermanyThe official EU CE declaration of conformity for this device may be f

iv About This Guide ENWW

Japanese Power Cord RequirementsFor use in Japan, use only the power cord received with this product.CAUTION: Do not use the power cord received with

HP Recycling ProgramHP encourages customers to recycle used electronic hardware, HP original print cartridges, andrechargeable batteries. For more inf

Turkey EEE RegulationIn Conformity with the EEE RegulationEEE Yönetmeliğine Uygundur36 Appendix C Agency Regulatory Notices ENWW

Table of contents1 Product Features ...

Preparing to Call Technical Support ... 25Locating the

1 Product FeaturesCompaq LCD MonitorsThe Compaq LCD (liquid crystal display) monitors have an active matrix, thin-film transistor (TFT) screenwith the

●Software and utilities CD, containing the following:◦Drivers◦Auto adjustment software◦Documents2 Chapter 1 Product Features ENWW

2 Safety and Maintenance GuidelinesImportant Safety InformationA power cord is included with the monitor. If another cord is used, use only a power so