Compaq DS10 Manual de usuario descargar pdf (Pagina 44)

3-16 Installing Linux on Alpha Systems

ide: Assuming 40MHz system bus speed for PIO modes; override with idebus=xx

ALI15X3: IDE controller on PCI bus 00 dev 68

ALI15X3: not 100% native mode: will probe irqs later

ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hda:pio, hdb:pio

ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdc:pio, hdd:pio

hda: COMPAQ CDR-8435, ATAPI CDROM drive

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

hda: ATAPI 32X CD-ROM drive, 128kB Cache, DMA

Uniform CDROM driver Revision: 2.56

Floppy drive(s): fd0 is 2.88M

FDC 0 is a post-1991 82077

LVM version 0.8e by Heinz Mauelshagen (4/1/2000)

lvm -- Driver successfully initialized

md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8

linear personality registered

raid0 personality registered

raid1 personality registered

qlogicisp : new isp1020 revision ID (5)

scsi0 : QLogic ISP1020 SCSI on PCI bus 00 device 78 irq 39 I/O base 0xb800

scsi : 1 host.

Vendor: COMPAQ Model: BB00921B91 Rev: 3B05

Type: Direct-Access ANSI SCSI revision: 02

Detected scsi disk sda at scsi0, channel 0, id 0, lun 0

scsi : detected 1 SCSI disk total.

SCSI device sda: hdwr sector= 512 bytes. Sectors= 17773524 [8678 MB] [8.7 GB]

Partition check:

sda: sda1 sda2 sda3 sda4

VFS: Mounted root (ext2 filesystem) readonly.

Freeing unused kernel memory: 208k freed

Adding Swap: 136544k swap-space (priority -1)

VFS: Disk change detected on device ide0(3,0)

ISO 9660 Extensions: RRIP_1991A

tulip.c:v0.91g-ppc 7/16/99 [email protected]

eth0: Digital DS21143 Tulip rev 65 at 0x8000, 08:00:2B:86:68:18, IRQ 29.

eth0: EEPROM default media type Autosense.

eth0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2)

block.

eth0: Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY (2)

block.

eth0: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4)

block.

eth0: Index #3 - Media 100baseTx-FD (#5) described by a 21143 SYM PHY (4)

block.

eth1: Digital DS21143 Tulip rev 65 at 0x8800, 08:00:2B:86:66:CA, IRQ 30.

eth1: EEPROM default media type Autosense.

eth1: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2)

block.

eth1: Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY (2)

block.

eth1: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4)

block.

eth1: Index #3 - Media 100baseTx-FD (#5) described by a 21143 SYM PHY (4)

block.

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 61 62

Comentarios a estos manuales

Sin comentarios

Compaq DS10 Manual de usuario Pagina 44

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Compaq DS10