Compaq ProLiant SL390s - G7 Server Guía de usuario Pagina 24
- Pagina / 87
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Setup 24
• Manual installation—Insert the operating system CD into the CD-ROM drive and reboot the server.
This process may require you to obtain additional drivers from the HP website
(http://www.hp.com/support).
For information on using these installation paths, refer to the SmartStart installation poster in the HP
ProLiant Essentials Foundation Pack, included with the server.
Powering up and configuring the server
To power up the server, press the Power On/Standby button.
While the server boots, RBSU and the ORCA utility are automatically configured to prepare the server for
operating system installation.
To configure these utilities manually:
• Press the F8 key when prompted during the array controller initialization to configure the array
controller using ORCA.
• Press the F9 key when prompted during the boot process to change the server settings using RBSU.
The system is set up by default for the English language.
For more information on the automatic configuration, refer to the HP ROM-Based Setup Utility User Guide
located on the Documentation CD.
Power down the server
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some
internal circuitry remain active until AC power is removed.
IMPORTANT: If installing a hot-plug device, it is not necessary to power down the server.
1. Back up the server data.
2. Shut down the operating system as directed by the operating system documentation.
NOTE: If the operating system automatically places the server in Standby mode, omit the next
step.
3. Press the Power On/Standby button to place the server in Standby mode. When the server activates
Standby power mode, the system power LED changes to amber.
IMPORTANT: Pressing the UID button illuminates the blue UID LEDs on the front and rear
panels. In a rack environment, this feature facilitates locating a server when moving between
the front and rear of the rack.
4. Disconnect the power cords.
The system is now without power.
- User Guide 1
- Intended audience 2
- Contents 3
- Contents 4 4
- Contents 5 5
- Component identification 6
- Front panel LEDs and buttons 7
- Rear panel components 8
- Rear panel LEDs and buttons 9
- System board 10
- System board switches 11
- NMI functionality 12
- Hard drive numbering 13
- Battery pack LEDs 14
- System fans 15
- GPU location 16
- Component identification 17 17
- Rack planning resources 18
- Optimum environment 19
- Temperature requirements 20
- Power requirements 20
- Rack warnings 21
- Installing hardware options 21
- Power down the server 24
- Registering the server 25
- Introduction 26
- Processor options 26
- Memory configurations 29
- Installing DIMMs 30
- Hard drive guidelines 31
- Expansion board options 32
- PCI riser board option 33
- Cabling 34
- Configuration and utilities 35
- HP ROM-Based Setup Utility 36
- Array Configuration Utility 37
- Management tools 39
- Erase Utility 40
- HP Systems Insight Manager 41
- Management Agents 41
- Redundant ROM support 41
- Diagnostic tools 42
- Integrated Management Log 43
- Array Diagnostic Utility 43
- Keeping the system current 44
- Care Pack 45
- Troubleshooting 46
- Symbols on equipment 47
- Warnings and cautions 47
- Symptom information 48
- Loose connections 49
- Service notifications 50
- Troubleshooting flowcharts 50
- General diagnosis flowchart 51
- Symptoms: 53
- Troubleshooting 55 55
- POST problems flowchart 56
- OS boot problems flowchart 57
- • Redundancy failure 60
- Troubleshooting 61 61
- System battery 62
- FCC rating label 63
- Class A equipment 63
- Class B equipment 63
- Modifications 64
- • EMC Directive 2004/108/EC 65
- Japanese notice 66
- BSMI notice 66
- Korean notice 67
- Chinese notice 67
- Laser compliance 67
- Battery replacement notice 68
- Electrostatic discharge 69
- Specifications 70
- Technical support 72
- Technical support 73 73
- Customer Self Repair 74
- Technical support 75 75
- Reparo feito pelo cliente 76
- Technical support 77 77
- Technical support 78 78
- Technical support 79 79
- Acronyms and abbreviations 80
- Voltage Regulator Down 84
- Index 85 85
- Index 86 86
- Index 87 87
Relacionado con productos y manuales para Servidores Compaq ProLiant SL390s - G7 Server
Servidores Compaq AlphaServer 160 Guía de usuario
(181 paginas)
(181 paginas)
Servidores Compaq ProLiant DL388e Guía de usuario
(127 paginas)
(127 paginas)
Servidores Compaq AlphaServer ES45 3B Especificaciones
(322 paginas)
(322 paginas)
Servidores Compaq AlphaServer GS60 Manual de usuario
(24 paginas)
(24 paginas)
Servidores Compaq AlphaServer 160 Manual de servicio
(564 paginas)
(564 paginas)
Servidores Compaq ProLiant Especificaciones
(78 paginas)
(78 paginas)
Servidores Compaq AlphaServer ES40 Manual de usuario
(18 paginas)
(18 paginas)
Servidores Compaq System/E25 Manual de usuario
(18 paginas)
(18 paginas)
Servidores Compaq AlphaServer ES40 Manual de usuario
(42 paginas)
(42 paginas)
Servidores Compaq A9890A - Smart Array 6402/128 RAID Controller Especificaciones rápidas
(32 paginas)
(32 paginas)
Servidores Compaq 1200 Guía de usuario
(256 paginas)
(256 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales