Compaq 4354R - StorageWorks Enclosure Storage Manual de servicio Pagina 159
- Pagina / 218
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 8
Backing Up the Subsystem, Cloning Data for
Backup, and Moving Storagesets
This chapter describes some common procedures that are not mentioned previously in this
guide. The following information is included in this chapter:
■ “Backing Up the Subsystem Configuration,” page 8–1
■ “Cloning Data for Backup,” page 8–2
■ “Moving Storagesets,” page 8–6
Backing Up the Subsystem Configuration
The controller stores information about the subsystem configuration in its nonvolatile
memory. This information could be lost if the controller fails or when you replace a
module in the subsystem.
Use the following command to produce a display that shows if the save configuration
feature is active and which devices are being used to store the configuration.
SHOW THIS_CONTROLLER FULL
The resulting display includes a line that indicates status and how many devices have
copies of the configuration. The last line shows on how many devices the configuration is
backed up.
The
SHOW DEVICES FULL command shows which disk drive are set up to back up the
configuration. The syntax for this command is shown below:
SHOW DEVICES FULL
- Compaq StorageWorks 1
- First Edition (June 2001) 2
- Part Number: AA-RFAUD-TE 2
- Contents 3
- Chapter 2 4
- Chapter 3 5
- About this Guide 15
- Text Conventions 16
- Symbols in Text 17
- Symbols on Equipment 17
- Rack Stability 18
- Configuration Flowchart 19
- About this Guide xxi 21
- Getting Help 22
- Compaq Technical Support 22
- Compaq Website 23
- Compaq Authorized Reseller 23
- Chapter 1 25
- Planning a Subsystem 25
- Defining the Subsystems 26
- Controller” 27
- Model 2200 Enclosure 28
- Selecting a Failover Mode 29
- —normal operation 30
- Multiple-Bus Failover Mode 31
- Selecting a Cache Mode 33
- Read Caching 34
- Read-Ahead Caching 34
- Write-Back Caching 34
- Write-Through Caching 34
- Enabling Mirrored Caching 35
- The Command Console LUN 35
- Enabling the CCL 36
- Disabling the CCL 36
- D100 D101 D120D0 D1 38
- Planning a Subsystem 1–15 39
- Assigning Unit Numbers 40
- 0). Unit D102 will 41
- CXO6455B 42
- Failover Mode 43
- SCSI-3 Mode 44
- SCSI-2 Mode 44
- Switch or hub 46
- Planning a Subsystem 1–25 49
- Planning a Subsystem 1–29 53
- SHOW command to list the LUN 54
- Planning Storage 55
- Where to Start 56
- Configuration Rules 57
- CXO5851B 58
- Planning Storage 2–7 61
- Planning Storage 2–9 63
- CXO6186B 64
- Choosing a Container Type 65
- Creating a Storageset Profile 66
- Planning Storage 2–13 67
- CXO7287A 68
- CXO4592B 69
- A'A 71
- C'C 71
- Operating 72
- CXO7289A 74
- Controller 75
- Defining a Partition 76
- Switches 77
- Changing Switches 78
- RAIDset Switches 78
- Initialization Switches 79
- Chunk Size 80
- Save Configuration 82
- Destroy/Nodestroy 82
- Geometry 82
- Unit Switches 83
- Storage Maps 83
- Planning Storage 2–31 85
- − example storage map 85
- Planning Storage 2–33 87
- − example storage map 87
- Planning Storage 2–35 89
- Planning Storage 2–37 91
- Preparing the Host System 93
- Preparing the Host System 3–3 95
- CXO7382A 96
- Making a Physical Connection 97
- FileSystem 98
- Mounting the Filesystem 99
- Using genvmunix 100
- File Utility 101
- Reading from the device, dd 102
- For V4.0G and V5.1x 103
- V4.0G Output 103
- V5.1x Output 103
- For V4.0G 104
- For V5.1x 105
- Chapter 4 107
- Before Installing the Agent 111
- Enter Subsystem Information 113
- Final System Configuration 115
- Reconfiguring the Agent 119
- −Can use the 120
- Removing the Agent 121
- Chapter 5 123
- Configuration Procedures 123
- CXO7181A 124
- Cabling a Single Controller 125
- Connections 126
- Configure Controller Settings 127
- Restart the Controller 128
- Verify Installation 130
- For V4.0G Use 130
- For V5.1x Use 130
- Setting Up a Controller Pair 131
- CXO6887B 132
- Configuring Devices 137
- Configuring a Stripeset 137
- Configuring a Mirrorset 137
- Configuring a RAIDset 138
- Configuring a Partition 140
- Preferring Units 142
- Configuration Options 143
- Enabling Autospare 144
- Deleting a Storageset 145
- Changing Device Switches 146
- Changing Initialize Switches 146
- Changing Unit Switches 146
- Chapter 6 147
- Chapter 7 149
- Figure 7–2. Example system 151
- CLI Configuration Example 152
- Chapter 8 159
- Cloning Data for Backup 160
- RUN CLONE 161
- Moving Storagesets 164
- Appendix A 167
- Subsystem Profile Templates 167
- Storageset Profile 168
- Enclosure 169
- BA370 Enclosure 170
- 4214R Disk Enclosure 172
- 4254 Disk Enclosure 173
- 4310R Disk Enclosure 175
- 4350R Disk Enclosure 177
- 4314R Disk Enclosure 178
- 4354R Disk Enclosure 180
- Appendix B 181
- Before You Install the Client 182
- Installing the Client 182
- During Installation 183
- Host to the Navigation Tree 185
- About the User Guide 188
- About the Online Help 188
- Glossary 189
Relacionado con productos y manuales para Arrays de discos Compaq 4354R - StorageWorks Enclosure Storage
(28 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales