Compaq DS10 Instrucciones de operaciones Pagina 106
- Pagina / 182
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2-54 DS10 / DS10L Console Reference
2.20 Running the AlphaBIOS Console
AlphaBIOS is the graphical interface that supports utility
programs.
NOTE: AlphaBIOS contains features and menus that support multiple
operating systems. The Windows NT operating system is not supported
on Compaq AlphaServer DS10/DS10L and AlphaStation DS10
systems. Only the AlphaBIOS features applicable to the Tru64 UNIX
and OpenVMS operating systems are discussed in this section.
After switching to AlphaBIOS, you will see the following screens.
Figure 2–1 AlphaBIOS Boot Screen
AlphaBIOS 5.70 (DS10 Beta 3)
Alpha Processor and System Information:
System: AlphaServer DS10
Processor: Digital Alpha 21264 600MHz
Memory: 256 MB
Alpha Processor(s) Status:
Processor 0 Running
TIG PAL Revision: 2:1
SCSI Controller Initialization
Initializing ATAPI #0
Device: Disk SCSI ID:0 FUJITSU MPD3108AT DD2
Initializing ATAPI #1
F2= Setup PAUSE=Pause Display ESC=Bypass Network Init
- AlphaServer DS10 / DS10L 1
- AlphaStation DS10 1
- September, 2000 2
- Contents 3
- Appendix A Setting Jumpers 6
- Examples 6
- Intended Audience 11
- Document Structure 11
- Conventions 12
- Documentation Titles 12
- Information on the Internet 12
- Chapter 1 13
- Operations 13
- Powering Up the System 14
- Operations 1-3 15
- Symbol Function 15
- Console Reference 16
- Power-Up Display 17
- Top 4 17 18
- Second from top 3 16 18
- Second from bottom 2 15 18
- Bottom 1 14 18
- Consoles 19
- Testing the disks (read only) 20
- Testing the System 20
- Booting Tru64 UNIX 21
- Operations 1-11 23
- Installing Tru64 UNIX 25
- Booting OpenVMS 27
- Username: 28
- Operations 1-17 29
- (boot ewa0.0.0.2.0 -flags 0) 31
- Installing OpenVMS 33
- Updating Firmware 36
- 1. Start LFU 37
- Operations 1-29 41
- 1.8.4 LFU Commands 45
- Using the Halt Button 48
- Halt Assertion 50
- 1.10.4 Disabling Autoboot 51
- Chapter 2 53
- SRM and AlphaBIOS Consoles 53
- Invoking the SRM Console 54
- Commands 55
- 2.2.2 Commands: Syntax 57
- Show Commands 60
- 2.3.2 Show Device 62
- 2.3.3 Show Memory 65
- 2.3.4 Show PAL 65
- 2.3.5 Show Power 66
- 2.3.6 Show Version 67
- Creating a Power-Up Script 68
- Example 2–9 Boot Command 71
- Testing the System 73
- Set Commands 76
- 2.8.2 Set Secure 77
- Secure Mode 78
- 2.9.2 Clear Password 79
- 2.9.3 Resetting the Password 80
- Stopping and Starting CPU 81
- Forcing a System Crash Dump 83
- Using Environment Variables 84
- 2.13.2 show envar 85
- Reading a File 89
- Initializing the System 90
- Finding Help 91
- 2.18.1 auto_action 94
- 2.18.2 bootdef_dev 94
- 2.18.3 boot_osflags 95
- 2.18.4 com1_baud 97
- 2.18.5 com1_mode 97
- 2.18.6 console 98
- 2.18.7 ew*0_mode 99
- 2.18.8 ew*0_protocols 99
- 2.18.9 kbd_hardware_type 100
- 2.18.10 language 100
- 2.18.11 os_type 101
- 2.18.12 password 101
- 2.18.13 pci_parity 102
- 2.18.14 pk*0_fast 102
- 2.18.16 pk*0_soft_term 103
- 2.18.15 pk*0_host_id 103
- 2.18.17 tt_allow_login 104
- OpenVMS operating systems 108
- Display Error Frames 109
- On Selection Setup… 109
- Run Maintenance Program… 109
- Location: A: 110
- Chapter 3 113
- RMC Components 114
- Terminal Setup 116
- Operating Modes 118
- 3.3.2 Bypass Modes 119
- Entering the RMC 120
- Status Monitoring 122
- RMC Power 123
- Remote Power (On/Off) 124
- RMC> power on 125
- Returning to COM port 125
- RMC> power off 125
- Remote Halt (In/Out) 126
- Configuring Remote Dial-In 128
- Configuring Dial-Out Alert 130
- 15085553333 132
- 5085553332# 132
- Dialing In 133
- Processor 134
- Troubleshooting Tips 136
- (Continued) 137
- RMC Commands 138
- 3.14.1 clear alert 140
- 3.14.2 clear port 140
- 3.14.3 disable alert 141
- 3.14.4 disable remote 141
- 3.14.5 enable alert 142
- 3.14.6 enable remote 143
- 3.14.7 halt (in/out) 144
- 3.14.8 hangup 145
- 3.14.9 help or ? 145
- 3.14.10 power off 146
- 3.14.11 power on 146
- 3.14.12 quit 147
- 3.14.13 reset 148
- 3.14.14 send alert 148
- 3.14.15 set alert 149
- 3.14.16 set com1_mode 150
- 3.14.17 set dial 151
- 3.14.18 set escape 152
- 3.14.19 set init 153
- 3.14.20 set logout 154
- 3.14.21 set password 154
- 3.14.22 set user 154
- 3.14.23 set wdt 155
- 3.14.24 status 155
- Appendix A 157
- Setting Jumpers 157
- Warnings and Cautions 158
- Open the System 161
- ➌ and pull it out 162
- ❹. Lift it off 162
- Setting Jumpers A-7 163
- ❶ on the top of the cover 164
- ❷ on the top of the cover 164
- PK1018-99 165
- Set Jumpers 166
- Restore Power 168
- Appendix B 169
- Regulatory Compliance Notices 169
- B.1.1 Class A Device Notices 170
- Taiwan Notice 171
- Japanese Notice 171
- B.1.2 Class B Device Notices 173
Relacionado con productos y manuales para Redes Compaq DS10
Redes Compaq CP-2E Guía de usuario
(91 paginas)
(91 paginas)
Redes Compaq 8/20q Especificaciones
(72 paginas)
(72 paginas)
Redes Compaq EK-ASIP2-OG. D01 Especificaciones
(78 paginas)
(78 paginas)
Redes Compaq HSZ80 Manual de servicio
(336 paginas)
(336 paginas)
Redes Compaq COM Express Extension Manual de usuario
(20 paginas)
(20 paginas)
Redes Compaq EVO NOTEBOOK N410C Manual de usuario
(14 paginas)
(14 paginas)
Redes Compaq 1124 Guía de usuario
(30 paginas)
(30 paginas)
Redes Compaq OSI/FTAM D43 Manual de usuario
(443 paginas)
(443 paginas)
Redes Compaq OSI/APLMGR D43 Manual de servicio
(130 paginas)
(130 paginas)
Redes Compaq LP8000-F1 Manual de usuario
(4 paginas)
(4 paginas)
Redes Compaq Tru64 UNIX Especificaciones rápidas
(39 paginas)
(39 paginas)
Redes Compaq LP8000-F1 Manual de usuario
(15 paginas)
(15 paginas)
Redes Compaq NC3134 Guía de usuario
(33 paginas)
(33 paginas)
Redes Compaq OSI/FTAM D43 Manual de usuario
(307 paginas)
(307 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.112 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales