Compaq 370 Guía de instalación Pagina 116
- Pagina / 186
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-2 Compaq ProLiant ML370 Setup and Installation Guide
Compaq Confidential – Need to Know Required
Writer: CDresden Project: Compaq ProLiant ML370 Setup and Installation Guide Comments:
Part Number: 120137-002 File Name: f-ch5 SCSI Cabling Instructions Last Saved On: 12/10/99 12:28 PM
SCSI Cabling Equipment
ProLiant ML370 servers are shipped with two preinstalled SCSI cables to
connect hard drives and removable media devices to an Integrated Dual
Channel Wide Ultra2 SCSI Controller port on the system board. The default
cabling configuration below shows a three-device, terminated SCSI cable
connecting SCSI port 1 to the removable media area
and a point-to-point
SCSI cable connecting SCSI port 2 to the hot-plug drive cage
.
Cables for any configuration involving standard or optional equipment are
provided with the server or with the appropriate option kit.
1
2
2
1
Figure 5-1. Default cabling configuration
Three-Device, Terminated SCSI Cable from SCSI
Port 1 to the Removable Media Area
The three-device cable shown above connects up to three SCSI devices,
which are installed in the removable media area. One end of the SCSI cable is
connected to SCSI port 1 of the server, the other end of the cable is bundled
inside the vacant bays of the removable media area and is not connected to any
SCSI device.
When you install SCSI devices in the removable media area, connect the
devices to this SCSI cable.
- ProLiant ML370 1
- Part Number 120137-002 2
- Contents 3
- Chapter 4 5
- Chapter 5 6
- Chapter 7 7
- Appendix A 7
- Appendix B 8
- Appendix C 8
- Appendix D 8
- Appendix E 9
- About This Guide 11
- Symbols in Text 12
- Symbols on Equipment 12
- Rack Stability 13
- Getting Help 14
- Compaq Authorized Reseller 15
- Server Features 16
- Customer Support 17
- Standard Features 18
- Disk Controllers 19
- Network Controller 20
- Removable Storage Media 20
- Standard Interfaces 21
- Warranty 22
- Default Configuration 23
- Compaq SmartStart 24
- Server Management 24
- Security Features 28
- Diagnostic Tools 28
- Front Panel Components 29
- Rack Model Server 30
- Rear Panel Components 31
- Table 1-6 35
- Chapter 2 36
- Installation Sequence 36
- Selecting a Site 37
- Unpacking 38
- Locating Materials 38
- Major Hardware Options 39
- Peripheral Devices 40
- Connecting the Power Cord and 40
- Power Cords 41
- Powering Up the Server 41
- Using Diagnostic Tools 44
- Registering Your Server 45
- Routine Maintenance 45
- Chapter 3 46
- Rack Warnings and Precautions 48
- The Optimum Environment 50
- Unpacking the Rack Server 52
- Table 3-1 54
- Rack Mounting Hardware 54
- Slide Rail Assemblies 56
- CZR4-006.eps 59
- CZR4-007.eps 59
- CZR4-008.EPS 60
- Applying the Template 61
- CZR4-009.EPS 62
- CZR4-011.eps 64
- Loading the Rack Server 66
- Attaching the Cable Support 72
- Optional Installation Service 79
- Installing Hardware Options 80
- Table 4-1 81
- Component Access 81
- Model Servers 82
- Opening the Front Bezel 83
- Tower Model 84
- 123 4 5 6 90
- Installing an Expansion Board 91
- 9. Turn on the computer 93
- Installing Additional Memory 94
- 7. Close the slot latches 95
- 8. Reassemble the server 95
- 10. Turn on the server 95
- Drive Cage 102
- Installing a Second Processor 104
- 6. Reassemble the server 105
- Board Brace 107
- Board Layouts 111
- Table 4-3 112
- Riser Board Components 112
- System Board Components 113
- Table 4-5 114
- SCSI Cabling Instructions 115
- SCSI Cabling Equipment 116
- Hot-Plug Hard Drive Cage 117
- Factory Default Configuration 119
- Hot-Plug Drives 121
- Media Devices 123
- Features 125
- Chapter 6 128
- System Configuration Utility 128
- Resolving Resource Conflicts 129
- System Configuration Menu 131
- Drive Array Configuration 132
- Power-On Defaults 132
- Configuration Backup 134
- Removing Boards 135
- SMP Operating System Support 136
- Loading Compaq Device Drivers 137
- Manual Installation 138
- Special Considerations 138
- LOAD A:\IDE\IDEATA.HAM 139
- LOAD A:\IDE\IDECD.CDM 139
- Device Drivers from Compaq 140
- Creating Utility Diskettes 141
- Retail Installation 144
- Controller Naming Conventions 146
- Table 6-2 146
- Integrated Management Log 148
- Compaq Insight Manager 149
- Compaq Survey Utility 150
- List of Events 151
- Table 7-1 152
- Event Messages 152
- Regulatory Compliance Notices 153
- Class A Equipment 154
- Class B Equipment 154
- Modifications 155
- European Union Notice 156
- Japanese Notice 157
- Taiwanese Notice 157
- Chinese Notice 157
- Laser Devices 158
- Battery Replacement Notice 159
- Electrostatic Discharge 161
- Grounding Methods 162
- Installing a New Battery 163
- Specifications and Connector 165
- Interfaces 165
- ° to 95°F10° to 35°C 166
- ° to 122°F-30° to 50°C 166
- °F 38.7°C 166
- Rack Model 167
- Power Supply 168
- Connector Interfaces 169
- Switches and Jumpers 170
- (SW2 Settings) 171
- NIC Operating Mode 171
- SCSI Device Jumper Settings 172
Relacionado con productos y manuales para Servidores Compaq 370
Servidores Compaq ProLiant SL165s Especificaciones
(117 paginas)
(117 paginas)
Servidores Compaq ProLiant DL388p Especificaciones
(106 paginas)
(106 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales