Compaq 370 Guía de instalación Pagina 96
- Pagina / 186
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installing Hardware Options 4-17
Compaq Confidential – Need to Know Required
Writer: Gilbert Saldivar Project: Compaq ProLiant ML370 Setup and Installation Guide Comments:
Part Number: 120137-002 File Name: e-ch4 Installing Hardware Options Last Saved On: 12/10/99 12:22 PM
Installing Additional Mass Storage
Devices
The server is shipped standard with a total of 10 drive bays for installing
additional internal mass storage devices. Non-SCSI devices including
CD-ROM drives and SCSI devices such as tape or hard drives can be installed
in the vacant non-hot-plug, removable media drive bays.
Six 1-inch SCSI hard drives can be installed in the standard hot-plug drive
cage (SCSI IDs 0-5). The orientation of the rack model is different from the
tower model shown in the figure below.
COMPACT
A
B
C
D
45 3210
Figure 4-15. SCSI ID locations (tower server)
NOTE: SCSI devices connected on port 1 of the Dual Channel Wide Ultra2 SCSI Controller
may be either internal or external drives, but not both.
- ProLiant ML370 1
- Part Number 120137-002 2
- Contents 3
- Chapter 4 5
- Chapter 5 6
- Chapter 7 7
- Appendix A 7
- Appendix B 8
- Appendix C 8
- Appendix D 8
- Appendix E 9
- About This Guide 11
- Symbols in Text 12
- Symbols on Equipment 12
- Rack Stability 13
- Getting Help 14
- Compaq Authorized Reseller 15
- Server Features 16
- Customer Support 17
- Standard Features 18
- Disk Controllers 19
- Network Controller 20
- Removable Storage Media 20
- Standard Interfaces 21
- Warranty 22
- Default Configuration 23
- Compaq SmartStart 24
- Server Management 24
- Security Features 28
- Diagnostic Tools 28
- Front Panel Components 29
- Rack Model Server 30
- Rear Panel Components 31
- Table 1-6 35
- Chapter 2 36
- Installation Sequence 36
- Selecting a Site 37
- Unpacking 38
- Locating Materials 38
- Major Hardware Options 39
- Peripheral Devices 40
- Connecting the Power Cord and 40
- Power Cords 41
- Powering Up the Server 41
- Using Diagnostic Tools 44
- Registering Your Server 45
- Routine Maintenance 45
- Chapter 3 46
- Rack Warnings and Precautions 48
- The Optimum Environment 50
- Unpacking the Rack Server 52
- Table 3-1 54
- Rack Mounting Hardware 54
- Slide Rail Assemblies 56
- CZR4-006.eps 59
- CZR4-007.eps 59
- CZR4-008.EPS 60
- Applying the Template 61
- CZR4-009.EPS 62
- CZR4-011.eps 64
- Loading the Rack Server 66
- Attaching the Cable Support 72
- Optional Installation Service 79
- Installing Hardware Options 80
- Table 4-1 81
- Component Access 81
- Model Servers 82
- Opening the Front Bezel 83
- Tower Model 84
- 123 4 5 6 90
- Installing an Expansion Board 91
- 9. Turn on the computer 93
- Installing Additional Memory 94
- 7. Close the slot latches 95
- 8. Reassemble the server 95
- 10. Turn on the server 95
- Drive Cage 102
- Installing a Second Processor 104
- 6. Reassemble the server 105
- Board Brace 107
- Board Layouts 111
- Table 4-3 112
- Riser Board Components 112
- System Board Components 113
- Table 4-5 114
- SCSI Cabling Instructions 115
- SCSI Cabling Equipment 116
- Hot-Plug Hard Drive Cage 117
- Factory Default Configuration 119
- Hot-Plug Drives 121
- Media Devices 123
- Features 125
- Chapter 6 128
- System Configuration Utility 128
- Resolving Resource Conflicts 129
- System Configuration Menu 131
- Drive Array Configuration 132
- Power-On Defaults 132
- Configuration Backup 134
- Removing Boards 135
- SMP Operating System Support 136
- Loading Compaq Device Drivers 137
- Manual Installation 138
- Special Considerations 138
- LOAD A:\IDE\IDEATA.HAM 139
- LOAD A:\IDE\IDECD.CDM 139
- Device Drivers from Compaq 140
- Creating Utility Diskettes 141
- Retail Installation 144
- Controller Naming Conventions 146
- Table 6-2 146
- Integrated Management Log 148
- Compaq Insight Manager 149
- Compaq Survey Utility 150
- List of Events 151
- Table 7-1 152
- Event Messages 152
- Regulatory Compliance Notices 153
- Class A Equipment 154
- Class B Equipment 154
- Modifications 155
- European Union Notice 156
- Japanese Notice 157
- Taiwanese Notice 157
- Chinese Notice 157
- Laser Devices 158
- Battery Replacement Notice 159
- Electrostatic Discharge 161
- Grounding Methods 162
- Installing a New Battery 163
- Specifications and Connector 165
- Interfaces 165
- ° to 95°F10° to 35°C 166
- ° to 122°F-30° to 50°C 166
- °F 38.7°C 166
- Rack Model 167
- Power Supply 168
- Connector Interfaces 169
- Switches and Jumpers 170
- (SW2 Settings) 171
- NIC Operating Mode 171
- SCSI Device Jumper Settings 172
Relacionado con productos y manuales para Servidores Compaq 370
Servidores Compaq ProLiant SL165s Especificaciones
(117 paginas)
(117 paginas)
Servidores Compaq ProLiant DL388p Especificaciones
(106 paginas)
(106 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.214 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales